国际隧道工程项目综合设计施工指南

近年来,我国工程承包商在国际市场得到长足发展,不但积累了大量项目经验,对于了解、研究国际标准及让国际社会深入了解中国标准的需求也不断增长,后者对于中国标准国际化亦有深刻意义。深入研究和了解ICE协会的出版物,是实现各项目标不可忽视的重要环节,我中心对ICE隧道工程规范(第三版)》(即Specification for Tunneling Third Edition,以下简称“ICEST”)进行深入研究,发现:

权威性。ICEST系由ICE和英国隧道工程协会(BTS)共同编制而成,其他文中已对ICE做出详细介绍,而BTS则是ICE的联合协会组织,成立于1971年,专注隧道工程,并针对行业实践发布相应的行业指南和实践守则,为政府和行业提供隧道指导建议,在英国、欧洲、英联邦国家及深受英国影响地区具有较高威信。

综合性。ICEST涉及隧道工程中的材料、施工方法、地层加固和工作环境,具体内容见本文第二部分;此外,标准是针对某一点进行深入研究,而ICEST则是综合和总结各项标准,举例来说,防水膜片性能要求则总结多项标准(见表1);此外,针对不同应用,ICEST给出可以结合参考使用的其他出版物,如涉及到明挖回填式隧道及类似地下洞室工程时,可结合参考《ICE打桩和嵌入式挡土墙规范(Specification for Pilingand Embedded Retaining Walls)》。

应用性和灵活性。从应用层面,ICEST是对英国、欧洲各国、欧洲及部分美国不同层面的隧道相关标准进行总结,为项目设计和施工提供依据,并在此基础上提出的框架性合同范本;此外,ICEST采用模块化编制方式,隧道工程承包商或设计单位可以根据具体项目采用相应条款,追溯相应标准依据,提出采用或不采用某一项标准、参数或方式方法的量化依据

1片状防水膜的性能要求

(摘自ICE隧道工程规范(第三版)第211.4节表6

性能

测试方法

要求

厚度

BS EN1849-2

2.0mm±10%

抗张强度

BS EN ISO527-3

16MPa

断裂伸长率

BS EN ISO527-3

不低于300%(-10%/±20%)

水压阻力

BS EN 1928方法B

1小时5

耐根穿刺

DDCEN/TS 14416

无穿透

撕裂强度

BS EN 12310-2

80N/mm

焊缝抗拉强度

BS EN 12317-2

下一条焊缝处出现裂缝

吸水率

BS EN ISO62

<4.0%

防火等级

BS EN ISO11925-2

自动灭火

烟雾等级

BS EN ISO11925

E

 

时效性和适用性。ICEST根据全球隧道工程行业的技术和标准发展不断更新和改进,并欢迎一线工程师和设计师对其提出建议和意见。我中心也将不断关注和研究各项出版物的发布和更新;ICEST适用于采用欧洲、英国标准体系的隧道工程项目,占我国海外工程项目的50%以上;ICEST的描述十分明确,描述逻辑和我国标准有异曲同工之妙,符合我国工程师和设计师的阅读习惯,并可根据结果追溯源头,有助于设计单位和施工单位了解各项标准的原理和计算依据。

 

下面列出隧道工程的材料、施工方法、地基加固工艺和工作环境目录:

1.材料:

1.1混凝土

1.2钢筋

1.3预制混凝土衬砌

1.4球状石墨铸铁(SGI)衬砌

1.5钢结构工程和钢衬

1.6顶管

1.7拱形支护和桁架梁

1.8木栓、销钉和锚杆

1.9喷射混凝土原材料

1.10片状防水膜

1.11喷涂防水膜

1.12密封垫

1.13空腔灌浆用水泥浆

1.14填料

1.15索环与螺栓

1.16勾缝与填缝料

1.17木料

2.施工方法

2.1隧道开挖

2.2钻孔

2.3临时工程与地面支护

2.4木桩、钉销接合与锚杆支护

2.5喷射混凝土

2.6地面拱形支护

2.7先撑

2.8爆破

2.9地下水

2.10超前探测

2.11竖井与隧道爆破

2.12防水膜片施工

2.13喷涂防水膜施工

2.14盾构施工

2.15泥水和土压平衡盾构设备

2.16敞口隧道钻进设备

2.17手动盾构和开放式机械盾构

2.18隧道掘进设备和盾构设备的操作

2.19顶管施工

2.20顶箱隧道施工

2.21分段式隧道衬砌施工

2.22密封垫

2.23灌浆

2.24勾缝与填缝

2.25非喷涂现场混凝土砌衬

2.26竖井

2.27木平巷

2.28隧道、竖井和地下工程允许偏差

2.29地下工程监测记录及控制

2.30测量和放样

3.地基加固工艺

3.1压缩空气作业法

3.2地基稳固和地下水控制用灌浆法

3.3冻结法

3.4降低地下水位法

3.5补偿灌浆法

4.工作环境

4.1临时电气装置

4.2施工通风

4.3照明

4.4噪音与振动

4.5出入口

4.6大气监测

4.7废物废水处理

4.8泄漏与渗漏

 

此外,隧道工程常用标准及出版物情况如下,您可在本网站下载中心下载相应清单:

·                     Eurocodes6

·                     欧洲标准:74

·                     英国标准:33

·                     瑞士标准:1

·                     德国标准:18

·                     美国标准:4

·                     其他文件:22

 

 

 

相关链接:

英国土木工程师学会(ICE)简介

英国土木工程师学会(ICE2017年最新出版物

英国土木工程师学会(ICE)推荐出版物


相关国际标准:

BS EN 1991-1-4:2005 欧洲规范1:结构上的作用— 第1-4部分:一般作用——风力作用 Eurocode 1: Actions on structures - Part 1-4: General actions - Wind actions
BS EN 1991-1-3:2003 +A1: 2015 欧洲规范 1——结构上的作用 第 1-3 部分:一般作用——雪荷载 Eurocode 1 - Actions on structures - Part 1-3: General actions - Snow loads
BS EN 1991-1-2:2002 欧洲规范1:对结构的作用— 第1—2部分:一般作用—对受火结构的作用 Eurocode 1: Actions on structures - Part 1-2: General actions - Actions on structures exposed to fire
BS EN 1991-1-1:2002 欧洲规范1—结构上的作用 第1-1 部分: 一般作用——建筑物的密度、自重和外加荷载 Eurocode 1: Actions on structures - Part 1-1: General actions - Densities, self-weight, imposed loads for buildings
BS EN 1997-1 2004 A1 2013(2014)欧洲规范7:岩土设计— 第1部分:总则    BS EN 1997-1 2004 A1 2013(2014)欧洲规范7:岩土设计— 第1部分:总则 Eurocode 7:Geotechnical design —Part 1: General rules
BS EN 1997-2:2007 欧洲规范7—岩土工程设计— 第2部分:场地勘察和试验 Eurocode 7. Geotechnical design. Ground investigation and testing    BS EN 1997-2:2007 欧洲规范7—岩土工程设计— 第2部分:场地勘察和试验 Eurocode 7. Geotechnical design. Ground investigation and testing

BS EN 1992-1-1 A1 2014(2015) 欧洲规范2:混凝土结构设计— 第1-1部分:一般规程与建筑设计规程  

BS EN 1993-1-4:2006+A1:2015 欧洲规范3-钢结构设计 第1-4部分:一般规则-关于不锈钢的补充规则 Design of steel structures. General rules. Supplementary rules for stainless steels
BS EN 1993-1-3:2006 欧洲规范3 —钢结构设计—第 1-3 部分: 一般规则 —冷成型构件和薄板的补充规则 .Eurocode 3. Design of steel structures. General rules
BS EN 1993-1-1:2005+A1:2014 欧洲规范3:钢结构设计— 第1-1部分:一般规定和建筑规定. Eurocode 3. Design of steel structures. General rules and rules for buildings
BS EN 1993-1-2:2005. 欧洲规范3:钢结构设计—— 第1-2 部分:总则——结构防火设计 Eurocode 3. Design of steel structures. General rules
BS EN 1992-3:2006 欧洲规范2:混凝土结构 设计—— 第3部分:储水和挡水结构 Eurocode 2. Design of concrete structures. Liquid retaining and containing structures
BS EN 1992-2:2005 欧洲规范2—混凝土结构 设计— 第2部分:混凝土桥梁--结构设计与细则 Eurocode 2. Design of concrete structures. Concrete bridges. Design and detailing rules
BS EN 1992-1-2:2004 欧洲规范2—混凝土结构设计 第1—2部分:一般规则——结构防火设计 Eurocode 2. Design of concrete structures. General rules
BS EN 1991-4:2006. 欧洲规范1:结构上的作用— 第4部分:筒仓和储罐 Eurocode 1. Actions on structures. Silos and tanks
BS EN 1991-3:2006 欧洲规范1:结构上的作用— 第3部分:由吊车和机器产生的作用 Eurocode 1. Actions on structures. Actions induced by cranes and machinery
BS EN 1991-2:2003 欧洲规范1——结构作用 第2 部分:桥梁结构的普通车辆荷载作用 Eurocode 1. Actions on structures. Traffic loads on bridges
BS EN 1991-1-7:2006 欧洲规范1——结构作用 第1-7 部分:一般作用---偶然荷载作用 Eurocode 1. Actions on structures. General actions
BS EN 1991-1-6:2005 欧洲规范1——结构作用 第1-6 部分:一般作用---施工荷载 Eurocode 1. Actions on structures. General actions. Actions during execution
BS EN 1991-1-5:2003 欧洲规范1——结构作用 第1-5 部分:一般作用---热力作用 Eurocode 1. Actions on structures. General actions. Thermal actions
BS EN 1993-6:2007. 欧洲规范3—钢结构设计 第6部分 吊车支撑结构Eurocode 3. Design of steel structures. Crane supporting structures
BS EN 1993-5:2007. 欧洲规范3-钢结构设计-第5部分:桩基 Eurocode 3. Design of steel structures. Piling
BS EN 1993-4-3:2007. 欧洲标准3—钢结构设计第4-3部分:管线 Eurocode 3. Design of steel structures. Pipelines
BS EN 1993-4-2:2007+A1:2017. 欧洲规范3—钢结构设计第 4-2 部分:罐体Eurocode 3. Design of steel structures. Tanks
BS EN 1993-4-1:2007+A1:2017. 欧洲规范3:钢结构设计— 第4-1 部分:筒仓Eurocode 3. Design of steel structures. Silos
BS EN 1993-3-2:2006.欧洲规范3:钢结构设计—第3-2部分:塔,桅杆和烟囱——烟囱 Eurocode 3. Design of steel structures. Towers, masts and chimneys
BS EN 1993-3-2:2006. 欧洲规范3:钢结构设计—第3-2部分:塔,桅杆和烟囱——烟囱 Eurocode 3. Design of steel structures. Towers, masts and chimneys
BS EN 1993-3-1:2006. 欧洲规范3:钢结构设计—第3-1部分:塔、桅杆和烟囱——塔和桅杆 Eurocode 3. Design of steel structures. Towers, masts and chimneys
BS EN 1993-2:2006. Eurocode 3. 欧洲规范3—钢结构设计—第二部分:钢桥Design of steel structures. Steel bridges
BS EN 1993-1-12:2007. 欧洲规范3 — 钢结构设计—第1-12部分:适用于S700及以下等级钢材的EN 1993扩展部分附加规则 Eurocode 3. Design of steel structures. Additional rules for the extension of EN 1993 up to steel grades S 700
BS EN 1993-1-11:2006. 欧洲规范3—钢结构设计—第1-11部分:受拉构件设计 Eurocode 3. Design of steel structures. Design of structures with tension components
BS EN 1993-1-10:2005. 欧洲规范3:钢结构的设计——第1-10 部分:材料的韧度和密度特性 Eurocode 3. Design of steel structures. Material toughness and through-thickness properties
BS EN 1993-1-9:2005. 欧洲规范3-钢结构设计 第1-9部分:抗疲劳设计 Eurocode 3. Design of steel structures. Fatigue
BS EN 1993-1-8:2005. 欧洲规范 3: 钢结构设计—第1-8 部分:节点设计 Eurocode 3. Design of steel structures. Design of joints
BS EN 1993-1-7:2007. 欧洲规范3 — 钢结构设计 — 第1-7部分:承受面外荷载的板式结构 Eurocode 3. Design of steel structures. Plated structures subject to out of plane loading
BS EN 1993-1-6:2007+A1:2017. 欧洲规范 3 — 钢结构设计 — 1-6: 壳体结构强度和稳定性 Eurocode 3. Design of steel structures. Strength and Stability of Shell Structures
BS EN 1993-1-5:2006+A1:2017 欧洲规范 3 — 钢结构设计 第 1-5 部分: 板式结构件 Eurocode 3. Design of steel structures. Plated structural elements
BS EN 1998-6:2005. 欧洲规范8—抗震结构设计—第6部分:塔架、桅杆与烟囱 Eurocode 8. Design of structures for earthquake resistance. Towers, masts and chimneys
BS EN 1998-5:2004. 欧洲规范8:结构抗震设计—第5部分:基础、挡土结构和岩土工程 Eurocode 8. Design of structures for earthquake resistance. Foundations, retaining structures and geotechnical aspects
BS EN 1998-4:2006. 欧洲规范 8 — 结构抗震设计 —第4部分:筒仓、储罐和管道 Eurocode 8. Design of structures for earthquake resistance. Silos, tanks and pipelines
BS EN 1998-3:2005.欧洲规范 8 — 结构抗震设计—第 3 部分: 建筑物评估和加固改造 Eurocode 8. Design of structures for earthquake resistance. Assessment and retrofitting of buildings
BS EN 1998-2:2005+A2:2011. 欧洲规范8—结构抗震设计—第2部分:桥梁Eurocode 8. Design of structures for earthquake resistance. Bridges
BS EN 1998-1:2004+A1:2013. 欧洲规范 8 :抗震结构设计-第1部分:一般规定、地震作用和建筑规定 Eurocode 8: Design of structures for earthquake resistance. General rules, seismic actions and rules for buildings
BS EN 1995-2:2004. 欧洲规范5:木结构设计—第2部分:桥 Eurocode 5. Design of timber structures. Bridges
BS EN 1995-1-2:2004. 欧洲规范5:木结构设计—第1-2部分:概述——结构防火设计 Eurocode 5. Design of timber structures. General
BS EN 1995-1-1:2004+A2:2014.欧洲规范5:木结构设计—第1-1部分:概述——通用规则和建筑规则 Eurocode 5: Design of timber structures. General. Common rules and rules for buildings
BS EN 480-12: 2005 混凝土、灰浆和灌浆外加剂——试验方法—— 第12部分:外加剂碱含量的测定 Admixtures for concrete, mortar and grout - Test methods –Part 12: Determination of the alkali content of admixtures
BS EN 480-11: 2005 混凝土、灰浆和灌浆外加剂——试验方法—— 第11部分:固化混凝土中气隙特性的测定 Admixtures for concrete, mortar and grout - Test methods –Part 11: Determination of air void characteristics in hardened concrete
BS EN 480-10: 2009 混凝土、灰浆和灌浆外加剂——试验方法—— 第10部分:水溶性氯化物含量的测定 Admixtures for concrete, mortar and grout - Test methods –Part 10: Determination of water soluble chloride content
BS EN 480-8: 2012 混凝土、灰浆和灌浆外加剂——试验方法—— 第8部分:常规干物料含量测定 Admixtures for concrete, mortar and grout - Test methods –Part 8: Determination of the conventional dry material content
BS EN 480-6:2005 混凝土、灰浆和灌浆外加剂——试验方法—— 第6部分:红外分析 Admixtures for concrete, mortar and grout - Test methods –Part 6: Infrared analysis
BS EN 480-5:2005 混凝土、灰浆和灌浆外加剂——试验方法—— 第5部分:毛细管吸收的测定 Admixtures for concrete, mortar and grout - Test methods –Part 5: Determination of capillary absorption
BS EN 480-4: 2005 混凝土、灰浆和灌浆外加剂——试验方法—— 第4部分:混凝土渗水性的测定 Admixtures for concrete, mortar and grout - Test methods - Part4: Determination of bleeding of concrete
BS EN 480-2:2006 混凝土、灰浆和灌浆外加剂——试验方法—— 第2部分:凝固时间测定 Admixtures for concrete, mortar and grout - Test methods – Part 2: Determination of setting time
BS EN 480-1: 2014 混凝土、灰浆和灌浆外加剂——试验方法—— 第1部分:基准混凝土和基准灰浆的试验 Admixtures for concrete, mortar and grout - Test methods –Part 1: Reference concrete and reference mortar for testing
BS EN 450-1: 2012 混凝土用粉煤灰 第1部分:定义、规范和合格标准 Fly ash for concrete Part 1: Definition,specifications and conformity criteria
BS EN 206: 2013+A1: 2016 混凝土—规范、性能、生产及合格性 Concrete — Specification, performance, production and conformity
BS EN 196-2: 2013 水泥实验法第2部分:水泥的化学分析 Method of testing cement Part 2: Chemical analysis of cement
BS EN 196-1:2005 水泥检验方法-第1部分:强度的测定 Methods of testing cement —Part 1: Determination of strength
BS EN 197-1-2011 水泥 第1部分:普通水泥的组成、规格和一致性标准 Cement. Composition, specifications and conformity criteria for common cements
BS EN 295-7 排水和排污用陶土管、配件和管接头—第7 部分:顶管用陶土管和接头的要求 Vitrified clay pipes and fittings and pipe joints for drains and sewers. Requirements for vitrified clay pipes and joints for pipe jacking
BS EN 933-1:2012 集料几何特性试验 第1部分:确定粒径分布—筛分方法
BS EN 933-2-1996 集料几何特性试验—第二部分:确定粒径分布—试验筛,筛眼公称尺寸
BS EN 933-3:2012 骨科几何性质的试验 第3部分:颗粒形状的测定 —片化指数
EN 933-8 确定骨料几何特性的试验 第8部分:纯度评估—含沙当量
BS EN 1097-8:2009 集料的机械特性和物理特性的试验 第八部分:抛光石料值的测定
BS EN 1097-6-2000 集料的力学性能和物理性能试验— 第6 部分:确定颗粒物的密度和吸水率
BS EN 1097-5:2008 集料力学和物理特性试验 第五部分:通过风箱干燥法确定含水量
BS EN 1097-3: 1998 骨料的机械与物理性能试验—第3部分:松散密度和孔隙率测定
BS EN 1097-2-2010 集料力学和物理特性试验 第二部分:测定破碎阻力的方法
EN 1744-1 测定颗粒材料化学性质的试验 第一部分 :化学分析

BS EN 1537-2000 中文 特殊岩土工程施工地锚 Execution of special geotechnical works. Ground anchors
BS EN 1916: 2002 中文 未加筋、钢筋和加筋混凝土管道和配件 Concrete pipes and fittings, unreinforced, steel fibre and reinforced
BS EN 934-2: 2009+A1: 2012 中文 砂浆、混凝土和水泥浆的附加剂 第2部分:混凝土附加剂---定义、要求、合规性、标记和标签 Admixtures for concrete, mortar and grout - Part 2: Concrete admixtures - Definitions, requirements, conformity, marking and labelling
BS EN 1562: 2012 中文 铸造—可锻铸铁 Founding — Malleable cast irons
BS EN 1011-1: 2009 中文 焊接—金属材料焊接建议 第1部分:电弧焊接通用指南 Welding —Recommendations for welding of metallic materials Part 1: General guidance for arc welding
BS EN 1008-2002 中文 混凝土混合用水—取样、测试、评估用水适宜性规范(包括将混凝土生产中的回收用水用作混凝土搅拌用水) Mixing water for concrete - Specification for sampling, testing and assessing the suitability of water, including water recovered from processes in the concrete industry, as mixing water for concrete
BS EN 10080:2005 中文 混凝土增强用钢 - 可焊接钢筋 - 总则 Steel for the reinforcement of concrete - Weldable reinforcing steel - General
BS EN 10025-5-2004 中文 热轧结构钢产品第五部分:增强型耐大气腐蚀结构钢交货技术条件 Hot rolled products of structual steels. Technical delivery conditons for structural steels with improved atmospheric corrosion resistance
BS EN 10025-4-2004 中文 热轧结构钢产品 第4部分:热机轧制可焊接细晶粒结构钢的交货技术条件 Hot rolled products of structural steels. Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels
BS EN 10025-3-2004 中文 热轧结构钢产品 第三部分: 标准及适于焊接的细晶粒结构标准卷轧钢制品交货技术条件 Hot rolled products of structural steels. Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels
BS EN 10025-2: 2004 中文 结构钢的热轧产品— 第二部分:非合金结构钢的技术供货条件 Hot rolled products of structural steels. Technical delivery conditions for non-alloy structural steels
BS EN 10025-1-2004 中文 结构钢热轧产品- 第一部分:一般技术交货条件 Hot rolled products of structural steels. General technical delivery conditions
BS EN 1563-2018 中文 铸造---球墨铸铁 Founding. Spheroidal graphite cast irons
BS EN ISO 1461-2009 中文 装配式钢铁制品的 热浸镀锌层—— 规范和试验方法 (ISO1461:2009) Hot dip galvanized coatings on fabricated iron and steel articles. Specifications and test methods
BS EN 772-2-1998 中文 砌体砌筑单元的试验方法— 第2 部分:集料混凝土砌体砌筑单元的孔隙面积百分比的测定(通过纸压痕法) Methods of test for masonry units. Determination of percentage area of voids in masonry units (by paper indentation)
BS EN 1011-2 :2001 中文 焊接 – 焊接金属材料的推荐 第2部分:铁素体钢的弧焊 Welding - Recommendations for welding of metallic materials - Arc welding of ferritic steels
BS EN 12350-1:2009 中文 新拌混凝土试验 第1部分:取样 Testing fresh concrete. Sampling
BS EN 12350-2:2009 新拌混凝土测试 第二部分:坍落度测试 Testing fresh concrete. Slump-test
BS EN 12350-3-2009 中文 新拌混凝土试验第3部分:维氏(稠度)试验 Testing fresh concrete. Vebe test
BS EN 12350-4-2009 中文 新拌混凝土试验-第4部分:压实度 Testing fresh concrete. Degree of compactability
BS EN 12350-6:2009 测试新拌混凝土--第6部分:密度 Testing fresh concrete--Part 6: Density
BS EN 12350-7-2009 中文 新拌混凝土试验 第7部分:空气含量——压力法 Testing fresh concrete. Air content. Pressure methods
BS EN 12350-11:2010 中文 新拌混凝土试验 第11部分:自压实混凝土 — 筛分离试验 Testing fresh concrete. Self-compacting concrete. Sieve segregation test
BS EN 12390-2:2009 中文 硬化混凝土试验 第二部分:制作和养护强度试验用试样 Testing hardened concrete. Making and curing specimens for strength tests
BS EN 12390-4:2000 中文 硬化混凝土的测试 第四部分: 抗压强度—试验器的规格 Testing hardened concrete. Compressive strength. Specification for testing machines
BS EN 12390-6-2009 中文 硬化混凝土试验— 第6部分:试样的劈裂抗拉强度 Testing hardened concrete. Tensile splitting strength of test specimens
BS EN 12390-7:2009 中文 硬化混凝土试验 第7部分:硬化混凝土密度 Testing hardened concrete. Density of hardened concrete
BS EN 12390-1: 2012 测试硬化混凝土 第1部分:试件和模具的形状、尺寸和其他要求 Testing hardened concrete Part 1: Shape, dimensions and other requirements for specimens and moulds
BS EN 12390-5-2009 硬质混凝土的测定 第五部分:试样的绕曲强度
BS EN 12390-3-2009 硬化混凝土试验 第3部分:试样的抗压强度